United States Department of Transportation

FHWA Highway Safety Programs

Safety Eligibility Letter SS-60A

Hardware Type:

Sign Supports, Mailboxes, and Delineator Posts

Code:

SS-60A

Date:

10/21/1996

Testing Criteria:

NCHRP 350

Manufacturer:

Clifford Dent

Device Description:

Larger bolts with same necked-down diameter

View PDF:

ss60a.pdf (4.31 MB)

Feedback

October 27, 1995

Refer to: HNG-14/SS60A

Mr. Clifford M. Dent
P.O. Box 1119
Mile 16.5 North Road
Kenai, Alaska 99611

This is in response to your facsimile letter to Mr. Nicholas Artimovich requesting Federal Highway Administration's (FHWA) acceptance of a modification to your breakaway sign support couplings. Our Geometric and Safety Design Acceptance Letter SS-60, dated October 27, 1995, found 12.7-mm (1/2-inch) and 15.9-mm (5/8-inch) couplings acceptable in a square (4-bolt) or a triangular (3-bolt) pattern. Your current request is to use increased diameter bolts, namely 3/4-inch, 7/8-inch and 1-inch (19.1-mm, 22.2-mm, and 25.4-mm respectively).

In our October 27, 1995, letter we conditioned our acceptance to sign installations "within the range of conditions tested." This means that sign supports that are substantially weaker in bending or more massive than the tested installation, which had a 127 x 127 x 4.76 steel tube support and a mass of 70.8 kg, would not be acceptable without further testing. The larger bolt sizes you wish to use are typically used with larger supports than those tested. The 4.5-m/s velocity change of the support tested with the 15.9-mm (5/8-inch)bolt is close to the acceptance limit, and a more massive installation may fail to meet the 5.0 m/s maximum allowable velocity change.

You have stated to Mr. Artimovich that some States have "over designed" their breakaway bases and use larger diameter bolts than are necessary to adequately support their sign installations. Some of these States wish to use your company's necked-down bolt in bases that were made for bolts larger than the two sizes of your bolt already found acceptable. We further understand that the larger bolts you wish to sell are only intended for use on sign installations of similar mass to those that were tested. With this understanding, we are willing to accept the use of the necked-down 3/4-inch, 7/8-inch, and l-inch

(19.1-mm, 22.2-m, and 25.4-mm) bolts, for three- or four-bolt, horizontal matched-plate bases subject to the following conditions:

1. Maximum mass per foot of sign post shall not exceed 30 kg/m (20 pounds per foot.)

2. Maximum mass of sign and support shall not exceed 100 kg (220 pounds).

3. Maximum perpendicular distance from a line connecting any two adjacent bolts to a parallel line through a third does not exceed 155 mm. (This will yield various maximum bolt circle diameters, depending on the bolt pattern (triangular, square, or rectangular) used.)

4. Maximum diameter at the grooved section shall not exceed 9.65 mm.

5. The mated plates are at least as stiff as the tested plates.

Because the material specifications of your galvanized, ASTM A325-type-material, steel bolts and the diameter of the critical necked-down section will not be changed, we concur in the use of the 19.1-mm, 22.2-m, and 25.4-mm necked-down bolts on the National Highway System if requested by a State. All other conditions in our October 27, 1995, letter remain in effect. Dimensions of all seven acceptable necked-down bolts are given in the enclosed table and shown in the enclosed drawings.

Sincerely yours,

Seppo I. Sillan, Acting Chief
Federal-Aid and Design Division

Supplemental Geometric and Roadside Design Acceptance Letter SS-60A
Attachment to letter dated October 21, 1996

Dimensions of Dent Breakaway Bolts.
Material: Conforms to the physical requirements of steel in finished ASTM A325 bolts
Finish: Galvanized
Dimensions in millimeters (dimensions in inches in parentheses)

Nominal Diameter	12.7 (0.50)	15.9 (0.625)	19.1 (0.750)	22.2 (0.875)	25.4 (1.00)	25.4 (1.00)	25.4 (1.00)
Dim. @ Neck Between Cones	7.1 1 (0.280)	9.65 (0.380)	9.65 (0.380)	9.65 (0.380)	9.65 (0.380)	7.1 1 (0.280)	9.65 (0.380)
Radius of Groove Between Cones	1.6 (0.0625)	1.6 (0.0625)	1.6 (0.0625)	1.6 (0.0625)	1.6 (0.0625)	1.6 (0.0625)	1.6 (0.0625)
Radius of Cone Bases	25.4 (1.00)	31.8 (1.25)	44.5 (1.75)	47.6 (1.875)	51 (2.00)	51 (2.00)	51 (2.00)
Distance Between Cone Bases	12.7 (0.50)	12.7 (0.50)	12.7 (0.50)	12.7 (0.50)	12.7 (0.50)	38.1 (1.50)	38.1 (1.50)
Height of Flats @ Cone Bases	1.6 (0.0625) minimum	1.6 (0.0625) minimum	1.6 (0.0625) minimum	1.6 (0.0625) minimum	1.6 (0.0625) minimum	1.6 (0.0625) minimum	1.6 (0.0625) minimum
Length of Bolt	115 (4.5)	115 (4.5)	133 (5.25)	133 (5.25)	133 (5.25)	178 (7.0)	178 (7.0)

FHWA Safety Home | FHWA Home | Feedback

United States Department of Transportation - Federal Highway Administration